Orion Car Audio XTREME 600.4 Manuel d'utilisateur

XTREME 600.4OWNER’S MANUALHIGH PERFORMANCE CAR AUDIO

TECHNICAL DESIGN FEATURESpage 10PRS PowerSupply12 GaugeSpeaker andRemoteATC Fuse4 Gauge Power& GroundComplementary MatchedBipolar OutputsRear Cros

TECHNICAL DESIGN FEATURESpage 111. Power LED - lights up when the amplifier is on2. Low-pass crossover frequency control-adjusts the front channellow-

SYSTEM PLANNING SYSTEM 1The easiest way to maximize the performance for yourORION XTREME amplifier is to properly plan your sys-tem. By planning your

SYSTEM PLANNING SYSTEM 2page 13System 2 is a two-way front / rearboomer system. Amplifier 1 powersfront and rear separates. Amplifier 2powers four

SYSTEM PLANNING SYSTEM 3page 14+–+–+–+–RGC-1+–+–+–+––++–+–+–

System 3 is a three-way tri-amplified system. Amplifier 1 is bi-amplified for the front separates. Amplifier 2 is configured for two-way operation.T

page 16SYSTEM PLANNING SYSTEM 4+–+–+–+–RGC-1+–+–+–+–

SYSTEM PLANNING SYSTEM 4System 4 is a four-way quad-amplified system. Amplifier 1 is bi-amplified for the front separates. Amplifier 2 is configured

INSTALLATIONThe installation of all ORION components will determine the overall performance result. Improper installation will not only limit the perf

page 19POWER CONNECTIONS• Minimum 8 gauge power and ground cable is recommended for acceptable performance• 4 gauge power and ground cable is recomme

TABLE OF CONTENTSINTRODUCTION 3WARRANTY 6SPECIFICATIONS 8TECHNICAL DESIGN FEATURES 10SYSTEM PLANNING 12INSTALLATION 18POWER CONNECTIONS 19SPEAKER CONN

SPEAKER CONNECTIONS 4-CHANNEL STEREO CONFIGURATION• Front and rear channel lowest recommendedimpedance is 2 ohm stereo• Crossover, output and gain con

SPEAKER CONNECTIONS 3-CHANNEL STEREO/BRIDGED CONFIGURATION• Front channels are configured for 2-channel stereooperation• Front channel lowest recommen

SPEAKER CONNECTIONS TWO-CHANNEL BRIDGED CONFIGURATION• Front and rear channels are configured for bridged 2-channel operation• Lowest recommended impe

SPEAKER CONNECTIONS TRI-MODE 6-CHANNEL CONFIGURATION• Lowest recommended impedance is 2Ω stereo and 4Ωbridged mono• Front and rear outputs must be set

4-CHANNEL AMPLIFIER INPUT CONFIGURATIONSThe 2-channel input / 4-channel input switch routes RCA input from the front RCA inputs to the rear section of

RCA INPUT / CH 1 & 2 XVRpage 25REAR INTERNAL CROSSOVER CONFIGURATIONThe XTREME 600.4 use multi-position switches to determine the rear crossover c

page 26When the switch is in the right position, the crossover is configured for low-pass operation. The rear channels of theXTREME 600.4 are continuo

page 27FRONT INTERNAL CROSSOVER CONFIGURATIONWhen the puch button switch is in the “off” position, the high-pass crossover is bypassed.When the push b

1,200 Hz10 kHz100 Hz350 HzFINE TUNING INTERNAL CROSSOVER85Hz2,500Hz 3,500HzWhen the puch button switch is in the “off” position, the high-pass crossov

INTELLI QIn the world of “me too features,” Orion has developed the INTELLi Q circuit that makes a real differencein your automotive listening experie

Thank you for your purchase of ORION’s XTREME amplifier. Each ORION amplifier is designed to be the leader in its class offering themost power, advanc

INTELLI QSetting up and using INTELLi Q1. The first step to using the INTELLi Q is to install the amplifier. Seriously, basic installation techniques

REMOTE GAINThe remote gain port allows remote, user control over the output of the amplifier. When used on asubwoofer amplifier, the remote gain allo

CHOOSING MOUNTING LOCATIONSThe location of your XTREME amplifier will depend on several important issues. Due to the low profile size of the XTREME am

GENERAL PRECAUTIONS AND INSTALLATION TIPSCaution: Be careful not to cut or drill into gas tanks, fuel lines, brake lines, hydraulic lines, vacuum line

STEP BY STEP INSTALLATIONStep 1 Determine the location for the amplifier. Refer to the Mounting Locations section in this manual for detailed informa

After you have completed the installation, you need to test the system. This will help ensure years of trouble-free operation. Please refer to thelist

ADJUSTING THE SOUND OF THE SYSTEMpage 36Once you have checked the system’s operation, adjust the sound of the system. Adjusting the sound of the sys

page 37

SYMPTOM PROBABLE CAUSE ACTION TO TAKENo output Low or no remote turn-on input Check remote turn-on voltage output at amplifier and fix as needed.Fuse

Distorted output Internal crossover not set properly Readjust crossovers. Refer to the Internal Crossover section of thisfor speakers manual for detai

ABOUT THIS MANUALThis manual is divided into different sections for different needs. Whether you are the owner, salesperson or installer, we have devo

AUTOSOUND 2000 TROUBLESHOOTING TIPSQUICK CHECK FOR TROUBLESHOOTING CAR AUDIO SYSTEMSPreface:All audio systems exhibit noise; however, if the level of

page 41II. DECK TO AMP. Using a new set of signal cables, connect one channel from the output of the deck directly into onechannel of your clean amp.

page 42probable that the component has inadequate isolation. Solutions include, changing components or permanently adding anexternal isolated power su

The more components installed on a signal path, the more chances for noise to enter a system. The more electrical accessorieson a car, the more noise

HIGH PERFORMANCE CAR AUDIOAMPLIFIERS, SIGNAL PROCESSORSAND LOUDSPEAKERS©1998 Orion Industries, Incorporated9235 S. McKemy St., Tempe, Arizona 85284Pho

(1) XTREME amplifier(1) 4 gauge power and ground connector(1) 12 gauge speaker and remote connector(4) #8 self-tapping black Phillips pan head screws(

WARRANTYORION Industries Inc. warrants this product to be free from defects in material and workmanship under the following terms:Parts and Labor are

This warranty is in effect for the original purchaser only. ORION will pay for labor and material expense for covered items. ORION doesnot cover remov

Amplifier Section XTREME 600.4 Front Channels XTREME 600.4 Rear ChannelsPower output 4 Ω stereo (watts)175 x 2 75 x 275 x 2, 300 x 1 75 x 2, 300 x 1Po

1All channels driven, continuous rated 4Ω load, 20Hz to 20,000Hz, >0.1% THD, per input voltage at 12.0VDC.2All channels driven, continuous rated 2Ω